First, the operation before entering the work area. Before entering the zone, the threshing clutch should be engaged smoothly to make the harvester run slowly. Then place the header, reel, etc. in the working position. Afterwards, a suitable gear is selected according to the crop condition, and finally the engine is placed at the rated speed and then the formal operation is started. The engine cannot be operated without reaching the rated speed to avoid clogging.
Second, the operation when turning: Should turn up the header while turning the ground, and then still use the big throttle to keep the engine running at rated speed. In order to reduce the speed of advancement, the method of lowering gear is used to reduce the speed, but it is not possible to reduce the speed by using the method of reducing the throttle, otherwise it will cause failure or blockage to the conveying, threshing and other parts.
Third, the operation of the windy days: the operation direction of the wind turbines harvesting operation unit should avoid the downwind movement; the air intake side of the cleaning mechanism on the windward side can be adjusted smaller, and the air inlet on the side of the leeward should be adjusted larger in order to balance. The amount of air flow reduces food losses and improves the quality of selection.
Fourth, when the slope passes through the operation: in the transfer of the ground, the road transport, through the slope, must pass through the slope, avoid the cross slope through, so as not to lose the high stability of the lateral stability of the harvester overturned. If the slope is large, you should reverse the car up and downhill.
V. Operation during car trapping: When you encounter a car trap, you must not attempt to cross it in the form of an out-of-the-way vehicle. Otherwise, the counter-productive action will be deeper and deeper, but you will not be able to get out of the trap. The correct way to deal with a car trap is to use a low throttle and a high speed, and use a low speed in the throttle. The wheels are riddled with stones, planks, sedges, etc. If there are shovels, the front of the trap can be dug. If one side is stuck in the car, you can use the differential to lock it, and open the differential lock immediately after it is out of the pit. When locked with a differential, the locomotive cannot be turned so as not to tip over, and it should remain in a straight line.
VI. Operation in the wet section: In the harvesting of paddy fields with less muddy feet in the paddy field, additional ground protection nets (boards) may be added to increase the adhesion and prevent the cars from collapsing; when harvesting the muddy feet, the joint The harvester's walking device was changed to a half-track type and then returned to operation.
VII. Operation of harvesting low crops: When rice blast grows low, the harvesting stage should strive to descend to the extent that it does not touch the ground. The reel should also be adjusted downwards and rearwards accordingly to prevent the attack on the ear of rice. It can increase the forward speed of the unit, thereby increasing the amount of feed, resulting in full-load feeding and improving work efficiency.
Eighth, the operation of harvesting lodging crops: the unit forward direction and the crop fall in the opposite direction, or about 45 degrees with the lodging direction angle, in order to avoid missing cut. Move the reel wheel forward and down properly; reduce the cutter height so as not to touch the ground; reduce the forward speed and other measures to reduce the loss.
9. Operation of over-ripe rice: When the rice straw is over-ripened, it is easy to lose grain and increase loss during harvest. In order to avoid excessive losses, the following actions should be taken: Adding some strips on the saw blade of the reel can make the efforts to increase the buffer and the role of cracking the valley, thereby reducing the loss of grain. At the same time, it is necessary to reduce the height of the reel, so that the reel can avoid the location of the ear and reduce the impact spike. It is also necessary to appropriately reduce the reel speed so as to reduce the number of blows and reduce the probability of grain dropping. When harvesting easy-to-fly pellets, a collector should be installed under the harvester roller to recover the pellets and promptly remove them.
10. Points to be taken when transferring a lot (1) When entering the ground, pay attention to the field ridge. If the slope is large, the speed should be slowed down, and the slope should be diagonally reversed through the field ridge to buffer the slope; if the reaping platform is scratched At this time, it is not possible to forcefully pass it. It must be passed by Tian Hao. (2) For small field cranes, the locomotive can be selected to pass in a vertical direction with the field ridge. When the harvesting platform is close to the field ridge, the hydraulic lifting handle should be pulled up to raise the header position, so that the header is raised and then slowly moved forward; when harvesting After the table passes, it is lowered to its normal position. (3) After the current round passes the field hoe, the hydraulic handle should be immediately pushed to the descending position, so that the header is lowered, maintaining the normal distance between the header and the ground, the current round has passed the ridge, and at the same time, the reaping platform is raised again, still maintaining and The ground is at a normal distance. (4) When the rear wheels pass through the field, as the rear wheel rises, the liquid header is raised again, thereby avoiding the header to touch the ground and damage the cutter. When the rear wheel passes, the header is returned to normal.
Note: Don't go straight through the field to save time and not to repeatedly lift the header, resulting in excessive bumps and damage to the cutting blade.
Second, the operation when turning: Should turn up the header while turning the ground, and then still use the big throttle to keep the engine running at rated speed. In order to reduce the speed of advancement, the method of lowering gear is used to reduce the speed, but it is not possible to reduce the speed by using the method of reducing the throttle, otherwise it will cause failure or blockage to the conveying, threshing and other parts.
Third, the operation of the windy days: the operation direction of the wind turbines harvesting operation unit should avoid the downwind movement; the air intake side of the cleaning mechanism on the windward side can be adjusted smaller, and the air inlet on the side of the leeward should be adjusted larger in order to balance. The amount of air flow reduces food losses and improves the quality of selection.
Fourth, when the slope passes through the operation: in the transfer of the ground, the road transport, through the slope, must pass through the slope, avoid the cross slope through, so as not to lose the high stability of the lateral stability of the harvester overturned. If the slope is large, you should reverse the car up and downhill.
V. Operation during car trapping: When you encounter a car trap, you must not attempt to cross it in the form of an out-of-the-way vehicle. Otherwise, the counter-productive action will be deeper and deeper, but you will not be able to get out of the trap. The correct way to deal with a car trap is to use a low throttle and a high speed, and use a low speed in the throttle. The wheels are riddled with stones, planks, sedges, etc. If there are shovels, the front of the trap can be dug. If one side is stuck in the car, you can use the differential to lock it, and open the differential lock immediately after it is out of the pit. When locked with a differential, the locomotive cannot be turned so as not to tip over, and it should remain in a straight line.
VI. Operation in the wet section: In the harvesting of paddy fields with less muddy feet in the paddy field, additional ground protection nets (boards) may be added to increase the adhesion and prevent the cars from collapsing; when harvesting the muddy feet, the joint The harvester's walking device was changed to a half-track type and then returned to operation.
VII. Operation of harvesting low crops: When rice blast grows low, the harvesting stage should strive to descend to the extent that it does not touch the ground. The reel should also be adjusted downwards and rearwards accordingly to prevent the attack on the ear of rice. It can increase the forward speed of the unit, thereby increasing the amount of feed, resulting in full-load feeding and improving work efficiency.
Eighth, the operation of harvesting lodging crops: the unit forward direction and the crop fall in the opposite direction, or about 45 degrees with the lodging direction angle, in order to avoid missing cut. Move the reel wheel forward and down properly; reduce the cutter height so as not to touch the ground; reduce the forward speed and other measures to reduce the loss.
9. Operation of over-ripe rice: When the rice straw is over-ripened, it is easy to lose grain and increase loss during harvest. In order to avoid excessive losses, the following actions should be taken: Adding some strips on the saw blade of the reel can make the efforts to increase the buffer and the role of cracking the valley, thereby reducing the loss of grain. At the same time, it is necessary to reduce the height of the reel, so that the reel can avoid the location of the ear and reduce the impact spike. It is also necessary to appropriately reduce the reel speed so as to reduce the number of blows and reduce the probability of grain dropping. When harvesting easy-to-fly pellets, a collector should be installed under the harvester roller to recover the pellets and promptly remove them.
10. Points to be taken when transferring a lot (1) When entering the ground, pay attention to the field ridge. If the slope is large, the speed should be slowed down, and the slope should be diagonally reversed through the field ridge to buffer the slope; if the reaping platform is scratched At this time, it is not possible to forcefully pass it. It must be passed by Tian Hao. (2) For small field cranes, the locomotive can be selected to pass in a vertical direction with the field ridge. When the harvesting platform is close to the field ridge, the hydraulic lifting handle should be pulled up to raise the header position, so that the header is raised and then slowly moved forward; when harvesting After the table passes, it is lowered to its normal position. (3) After the current round passes the field hoe, the hydraulic handle should be immediately pushed to the descending position, so that the header is lowered, maintaining the normal distance between the header and the ground, the current round has passed the ridge, and at the same time, the reaping platform is raised again, still maintaining and The ground is at a normal distance. (4) When the rear wheels pass through the field, as the rear wheel rises, the liquid header is raised again, thereby avoiding the header to touch the ground and damage the cutter. When the rear wheel passes, the header is returned to normal.
Note: Don't go straight through the field to save time and not to repeatedly lift the header, resulting in excessive bumps and damage to the cutting blade.
Ceramic Teapot is a mouthpiece used to make and pour tea. It is a kind of tea service, mainly used for making tea. The teapot consists of four parts: the lid, the body, the bottom and the feet. When making tea, the size of the teapot depends on the number of tea drinkers.The quality of the teapot is very much, at present USES more is violet arenaceous pottery pot or ceramic teapot. Before using the new teapot, you can put some tea leaves into the pot for a few more blisters. It's better to soak them a few more times. It is better to scrub with the soaked tea leaves.
Joy Tea Co.,LTD. has a professional design team, which can be customized for you. Welcome you to visit our company. For inqury, please send mail directly.
Ceramic Teapot
Ceramic Teapot,White Ceramic Teapot,Antique Ceramic Teapot,Square Ceramic Teapot
JOY TEA CO., LTD. , http://www.joyteaco.com