1. At the beginning of operation, the rotary cultivator shall be in the lifting state, firstly combined with the power output shaft to increase the rotation speed of the knife shaft to the rated rotation speed, and then dropping the rotary tiller to gradually insert the blade into the required depth. It is strictly forbidden to insert the blade into the soil and then combine the power output shaft or the drooping rotavator to avoid bending or breaking the blade and increasing the load of the tractor. 2. In the operation, you should try to slow down at a low speed. This will not only ensure the quality of the work, make the soil block fine, but also reduce the wear of the parts. Pay attention to listening to whether the rotavator has noise or metal knocking noise, and observe the smashed soil and the depth of cultivation. If there is any abnormality, the machine should be shut down for inspection immediately. 3. When turning in the ground, the operation is prohibited. The rotary cultivator should be lifted to move the blade off the ground and reduce the throttle of the tractor so as not to damage the blade. When the rotary cultivator is lifted, the tilt angle of the gimbal operation should be less than 30 degrees. When it is too large, it will produce impact noise, causing premature wear or damage. 4. When reversing, passing the field and transferring the plot, the rotary cultivator should be raised to the highest position and the power should be cut off to avoid damage to the components. If you move to a distant place, use a locking device to secure the rotary cultivator. 5. After each shift operation, the rotary cultivator shall be maintained. Remove dirt and weeds from the blades, inspect tightening of the connections, add lubricant to each lubricating point, and add grease to the joints to prevent increased wear.
Rotary cultivator adjustment
1. Left and right level adjustments. Park the tractor with the rotary tiller on the flat ground, lower the rotary tiller, and make the blade 5 cm away from the ground. Observe whether the left and right tip heights are the same from the ground to ensure that the cutter shaft level is consistent and the tillage depth is uniform during operation. 2. Adjust horizontally before and after. When the cultivator is lowered to the required depth of cultivation, observe whether the joint angle and the axis of the rotary cultivator are close to the horizontal position. 2. If the joint angle is too large, adjust the pull-up lever so that the rotary cultivator is in a horizontal position. 3. Increase height adjustment. Rotary tillage operation, the joint angle of the joint is not allowed to be greater than 10 degrees, the land is not allowed to turn more than 30 degrees. Therefore, the lifting of the rotary cultivator is limited to the proper position of the handle for the use of the available screws for position adjustment; when using the height adjustment, special attention must be paid when lifting, and if it is necessary to raise the rotary cultivator, the power of the universal joint should be cut off. .
Road Milk Tanker (Milk Tank trailer)5-60tons:
All the heads are one time moulding . And all the inner Rcorners are larger than 30mm.To ensure there is no right-angle inside the tank. the insulation layer PUF. Temperature raise less than 2°C within 24 hrs:
1.About the material:
AISI/SUS 304-2B(S.S304)food grade stainless steel plate sheet ,inside shell 2.5-3mm / outer shell 2mm, one time molding heads.
2 .Special welding process :
TIG welding process, to obtain the good outlook and reduce the crack and pit. All surface can be polished shinning like mirror.
3.One time molding heads and injecting PUF or use fiber glass.
And each compartment use double heads back-to-back which make sure every compartment heads smooth and no right-angle left,easy to wash.
Using polyurethane foam(PUF) /glass fiber to get better insulation ability, which has the perfect warmth keeping ability and ensure temperature raise not too fast
4.Milk out-let pipe and air vent
Each milk compartment has one set separate out-let pipe and air vent.out-let pipes which usesΦ50×2.0 polished stainless steel (sanitary parts), all pipes inside the insulation layer to make sure no frozen milk occurs in winter and no milk rotten in summer.
5.The CIP cleaning system
Equipment with automatic self-rotation ball(spray cleaning ball) inside the tank, and CIP joint in rear carbin.
6. Rear cabinet for tools/pipe /pump/and milk sampling.
The lockable rear cabinet design make the tanker have a tidy general look.and convenient for use/you add other device( according yourdesign).
7.The design of the manhole cover
All the covers are Anti-Spillage design, to avoid the over flow and leakage of the milk from top cover.
8.The Top anti-skid platform.
Anti-skid platform on the top of tank body made of Aluminium alloy plate with skid-resistant surface. For safyty.the anti-skidplatform with Φ25mm handrails(S.S) of 250mm height.
9.The breath airway(air vent):
Air vent diameter no less than Φ120mm.
10 .The tank body design:
The scientific long axis and short axis design for tank body meets the hydrokinetics requirements and ensures the safety of vehicles.and we can design the tank according your trailer(truck) size.
11 .The chassis of the vehicle
The vehicle chassis standard FAW chassis.or we provide semi-trailer chassis according your demand.
Road Milk Tanker
Milk Tanker,Road Milk Tanker,Milk Tanker Trailer,Transport Milk Tank Truck
Henan Leo Husbandry Equipment Science and Technology Co.ltd , https://www.chinaleodairy.com