Before using the V-type mixer, it is necessary to understand the operating procedures in detail, which is very important for its maintenance and the service life of the machine, as well as the safety of the operators. Below I combine years of operational experience to explain in detail how to step by step. V-type mixer 1. Inspection work before equipment operation:
1. Check that there should be no foreign matter in the mixer. The inner wall of the hopper should be dry. The V-type mixer closes the feeding port and the discharging port.
2. Turn on the mixer power button and rotate the stop button to the left. The power indicator should be correctly displayed in red.
3, check the mixing machine should be free of obstacles, so as to avoid the magnetic machine hitting the obstacle when the mixer is running, causing an accident.
4. After the above operation parameters are required, the following operations can be performed.
2. No-load operation:
1. Start the reverse button of the mixer to adjust the motor speed. The mixer should run at a slow reverse speed.
2. During the operation of the mixer, the fuselage should be operated at a constant speed without abnormal noise. After running for 1-2 minutes, prepare to stop.
3. Stop the machine by adjusting the motor speed button. When the machine is stopped, the mixer discharge port should be facing the ground, and adjust the motor speed button to 0 position. Turn the stop button to the right to cut off the power.
4. After the no-load operation meets the requirements, the following operations can be performed.
3. Strip operation (mixing):
1. Open the feeder feed port and re-confirm that the discharge port is closed, and put a specified amount of material into the V-type hopper according to the process control requirements.
2. After the feeding is completed, close the feeding port and lock it to prevent the material from flowing out during the mixing.
3. Turn on the power button, rotate the stop button to the left, start the reverse button of the mixer, and adjust the motor speed to mix in the specified speed of the process (* product requirement 600r/min).
4. After the mixture reaches the specified time of the process, stop by adjusting the motor speed button. When the machine stops, the mixing machine discharge port should be facing the ground, and adjust the motor speed button to 0 position. The V-type mixer will stop the button. Rotate to the right to turn off the power.
5. Discharge: Open the feeding port and fill the material at the discharge port with the specified container until the material in the hopper is drained.
1. Check that there should be no foreign matter in the mixer. The inner wall of the hopper should be dry. The V-type mixer closes the feeding port and the discharging port.
2. Turn on the mixer power button and rotate the stop button to the left. The power indicator should be correctly displayed in red.
3, check the mixing machine should be free of obstacles, so as to avoid the magnetic machine hitting the obstacle when the mixer is running, causing an accident.
4. After the above operation parameters are required, the following operations can be performed.
2. No-load operation:
1. Start the reverse button of the mixer to adjust the motor speed. The mixer should run at a slow reverse speed.
2. During the operation of the mixer, the fuselage should be operated at a constant speed without abnormal noise. After running for 1-2 minutes, prepare to stop.
3. Stop the machine by adjusting the motor speed button. When the machine is stopped, the mixer discharge port should be facing the ground, and adjust the motor speed button to 0 position. Turn the stop button to the right to cut off the power.
4. After the no-load operation meets the requirements, the following operations can be performed.
3. Strip operation (mixing):
1. Open the feeder feed port and re-confirm that the discharge port is closed, and put a specified amount of material into the V-type hopper according to the process control requirements.
2. After the feeding is completed, close the feeding port and lock it to prevent the material from flowing out during the mixing.
3. Turn on the power button, rotate the stop button to the left, start the reverse button of the mixer, and adjust the motor speed to mix in the specified speed of the process (* product requirement 600r/min).
4. After the mixture reaches the specified time of the process, stop by adjusting the motor speed button. When the machine stops, the mixing machine discharge port should be facing the ground, and adjust the motor speed button to 0 position. The V-type mixer will stop the button. Rotate to the right to turn off the power.
5. Discharge: Open the feeding port and fill the material at the discharge port with the specified container until the material in the hopper is drained.
Others Kiosk,Way Finding Digital Signage,Custom Standing Screen,Lcd Touch Screen Display
Shenzhen Sunson Tech Co., Ltd , https://www.sunsonkiosk.com