When agricultural vehicles are on the way, they cannot be repaired due to damage to parts, and when no new parts are replaced, some temporary emergency measures must be taken to repair them. Here are some common emergency repair methods:
When the burned area of ​​the cylinder pad burns is small, the asbestos line can be used to fill in. When the burned area is large, a piece of shimming can be cut from the same part of the waste cylinder pad of the same thickness and carefully tapped to make the two The combination is good; if the burnout is between two cylinders, the asbestos thread needs to be wrapped in copper skin.
If the inlet and outlet hoses are broken, if there is some breakage, use a piece of soap on the tape to wrap the leaks and tie them with wire or string; if it breaks severely, remove the hose from the break. Cut into two sections with a knife, first use a suitable bamboo tube or thin iron tube, etc., and put it between the hoses, and then tie it with iron wire or string, and then install it.
Radiator Breaking Radiator When the flat copper tube of the core has a slight leakage, the leak can be glued with soap; if the water leakage is serious, the leakage of the flat copper tube can be pinched gently with pliers so that it does not leak water.
If the valve spring breaks only one break, the two break springs can be installed and used. If the spring breaks several places, the multi-cylinder machine can remove the adjusting bolts of the intake and exhaust valves of the cylinder and the valve can be maintained. Close the state, at the same time should cut off the oil, so that the cylinder stops working.
The leaf spring breaks off According to the broken condition, the board spring is put between the leaf spring, the axle and the frame, and is temporarily tied with iron wire or rope, and is driven to the repair point for replacement.
Fan tape damage Fan tape damage is generally more broken phenomenon. The emergency method is: Several strands can be used for tightening the rope, and its length and thickness should be similar to those of the original fan tape (note that the rope should be caught in the middle, do not expose it to prevent it from biting during rotation), and then tighten it with iron wire. It is also possible to drill a small hole at the two ends of the original fan tape, and use them together for temporary use. When using the above method, the engine should be first commissioned for a few minutes to check if the fan rotation is normal and then drive again.
Sudden power cut in the middle of the road When suddenly the horn does not ring, the lights are not turned on, and the starter does not turn, it means that the vehicle has been completely powered off. At this time, you can first test the two piles of the battery (not to check the chaos when the inspection, you can use pliers pliers fork pile head), if there is no spark during the touch, then the pile head loose, tighten with a wrench. If the pile head is tightened or cleaned, the power-off phenomenon has not been eliminated, and the connection of the two-pole wires can be checked. If the contact is poor, the symptomatic repairs are required. After the above-mentioned short-circuit condition is eliminated and the power is still off, the individual cells of the battery should be tested. If a single cell is damaged, a good cell can be directly connected by using a copper wire or a wire.
Clutch slip If the friction plate is oily and slippery, you can step on the clutch pedal, install gasoline with the oil gun, aim at the gap between the flywheel, friction plate, and clutch pressure plate, so that the above oil is affected by gasoline and melted. The removal can be temporary (such as when no oil gun and other objects are used instead, the plastic pipe or the rubber pipe can be used to suck the gasoline in alignment with the shot); if the friction plate slips due to burning, the burned part is roughened You can, but you must start steadily when driving, and shift quickly.
When there is no jack to change the tire and replace the tire with the double row of tires, the inner wheel can be lifted by using wood or bricks (stones) to make the outer wheel vacant, so that it can be replaced; when replacing the tires in a single or double row of tires, Can use a flat top wood inclined roof under the front axle rear axle which needs to change the tire, then slowly open the car so that the top wood will lift the front axle or the rear axle. When the top wood is vertically stabilized, the tire can be replaced. .
When the burned area of ​​the cylinder pad burns is small, the asbestos line can be used to fill in. When the burned area is large, a piece of shimming can be cut from the same part of the waste cylinder pad of the same thickness and carefully tapped to make the two The combination is good; if the burnout is between two cylinders, the asbestos thread needs to be wrapped in copper skin.
If the inlet and outlet hoses are broken, if there is some breakage, use a piece of soap on the tape to wrap the leaks and tie them with wire or string; if it breaks severely, remove the hose from the break. Cut into two sections with a knife, first use a suitable bamboo tube or thin iron tube, etc., and put it between the hoses, and then tie it with iron wire or string, and then install it.
Radiator Breaking Radiator When the flat copper tube of the core has a slight leakage, the leak can be glued with soap; if the water leakage is serious, the leakage of the flat copper tube can be pinched gently with pliers so that it does not leak water.
If the valve spring breaks only one break, the two break springs can be installed and used. If the spring breaks several places, the multi-cylinder machine can remove the adjusting bolts of the intake and exhaust valves of the cylinder and the valve can be maintained. Close the state, at the same time should cut off the oil, so that the cylinder stops working.
The leaf spring breaks off According to the broken condition, the board spring is put between the leaf spring, the axle and the frame, and is temporarily tied with iron wire or rope, and is driven to the repair point for replacement.
Fan tape damage Fan tape damage is generally more broken phenomenon. The emergency method is: Several strands can be used for tightening the rope, and its length and thickness should be similar to those of the original fan tape (note that the rope should be caught in the middle, do not expose it to prevent it from biting during rotation), and then tighten it with iron wire. It is also possible to drill a small hole at the two ends of the original fan tape, and use them together for temporary use. When using the above method, the engine should be first commissioned for a few minutes to check if the fan rotation is normal and then drive again.
Sudden power cut in the middle of the road When suddenly the horn does not ring, the lights are not turned on, and the starter does not turn, it means that the vehicle has been completely powered off. At this time, you can first test the two piles of the battery (not to check the chaos when the inspection, you can use pliers pliers fork pile head), if there is no spark during the touch, then the pile head loose, tighten with a wrench. If the pile head is tightened or cleaned, the power-off phenomenon has not been eliminated, and the connection of the two-pole wires can be checked. If the contact is poor, the symptomatic repairs are required. After the above-mentioned short-circuit condition is eliminated and the power is still off, the individual cells of the battery should be tested. If a single cell is damaged, a good cell can be directly connected by using a copper wire or a wire.
Clutch slip If the friction plate is oily and slippery, you can step on the clutch pedal, install gasoline with the oil gun, aim at the gap between the flywheel, friction plate, and clutch pressure plate, so that the above oil is affected by gasoline and melted. The removal can be temporary (such as when no oil gun and other objects are used instead, the plastic pipe or the rubber pipe can be used to suck the gasoline in alignment with the shot); if the friction plate slips due to burning, the burned part is roughened You can, but you must start steadily when driving, and shift quickly.
When there is no jack to change the tire and replace the tire with the double row of tires, the inner wheel can be lifted by using wood or bricks (stones) to make the outer wheel vacant, so that it can be replaced; when replacing the tires in a single or double row of tires, Can use a flat top wood inclined roof under the front axle rear axle which needs to change the tire, then slowly open the car so that the top wood will lift the front axle or the rear axle. When the top wood is vertically stabilized, the tire can be replaced. .
Urine Centrifuge,Urinalysis Equipment,Laboratory Urinalysis Equipment,Urine Test Equipment
Changchun Medicon Technology Development Co., Ltd , http://www.jlmdk.com