1. The quality of the die must be checked repeatedly before use, whether there are missing edges, cracks, deformation and looseness, and whether the device is intact and good.
2. Check whether the powder of the granular material is dry and the powder content in the granules is not more than 10%. If it is not qualified, do not press hard, otherwise it will affect the normal operation and service life of the machine and the loss of raw materials.
3. For the first test run, place the indicator needle controlled by the pressure regulator on the 6th, pour the powder into the bucket, turn the test wheel by hand, adjust the filling and pressure, and gradually increase the weight and hardness of the tablet. Finished product requirements, then start the motor, then open the clutch, for the official operation of production, in the production process, the quality of the tablet must be checked regularly, whether it meets the requirements, if necessary, adjust.
4. The choice of speed has a direct impact on the service life of the machine. Due to the intrinsic viscosity of the material and the size and pressure of the material, the structure of the machine can not be uniformly defined. The structure of the machine has a stepless speed change device, which is suitable for suppressing minerals at a slow speed. Plant grass, large diameter, poor viscosity, etc. and materials that are difficult to form quickly. Quickly suitable for press bonding, good slip and easy to form materials. Therefore, the user must be determined according to the actual situation.
5. The management personnel must be familiar with the technical performance of the machine, the internal structure, the use principle of the control mechanism and the work place during the operation, to prevent damage to the machine parts, so as to ensure safe production.
6, in the use should always pay attention to whether the machine sound is normal, in case of screams and strange sounds to stop the inspection to eliminate, do not use barely.
7. Do not remove the protective cover, safety cover, etc. on the machine and equipment, and install it when using it.
8. The die needs to undergo strict flaw detection test and shape inspection. It should be crack-free, deformed, missing, and the hardness is suitable and the size is accurate. If it is unqualified, do not use it to avoid serious damage to the machine.
9. The feeding device and the turntable are flat, high and low accurate. If it is high, it will cause leakage of powder, while at low, it will affect the quality of the tablet.
10, do not use more raw materials, because it will make more powder on the upper, more leakage under the impact, affecting the wear and tear of the parts and the loss of raw materials.
11. Do not use raw materials that are not dry, as it will cause the powder to stick to the punch surface.
12. If there are jumps or stagnation during operation, do not use your hands to avoid accidents.
13. Drive the motor first, and then turn the clutch after the operation is normal.
14. If the machine vibration is abnormal or abnormal noise occurs during use, stop it immediately.
15, the use of medium pressure should not be too large, generally measured by the load of the motor, with a 380 volt motor in the tablet when the heavy-duty current is not more than 4 amps is normal.
2. Check whether the powder of the granular material is dry and the powder content in the granules is not more than 10%. If it is not qualified, do not press hard, otherwise it will affect the normal operation and service life of the machine and the loss of raw materials.
3. For the first test run, place the indicator needle controlled by the pressure regulator on the 6th, pour the powder into the bucket, turn the test wheel by hand, adjust the filling and pressure, and gradually increase the weight and hardness of the tablet. Finished product requirements, then start the motor, then open the clutch, for the official operation of production, in the production process, the quality of the tablet must be checked regularly, whether it meets the requirements, if necessary, adjust.
4. The choice of speed has a direct impact on the service life of the machine. Due to the intrinsic viscosity of the material and the size and pressure of the material, the structure of the machine can not be uniformly defined. The structure of the machine has a stepless speed change device, which is suitable for suppressing minerals at a slow speed. Plant grass, large diameter, poor viscosity, etc. and materials that are difficult to form quickly. Quickly suitable for press bonding, good slip and easy to form materials. Therefore, the user must be determined according to the actual situation.
5. The management personnel must be familiar with the technical performance of the machine, the internal structure, the use principle of the control mechanism and the work place during the operation, to prevent damage to the machine parts, so as to ensure safe production.
6, in the use should always pay attention to whether the machine sound is normal, in case of screams and strange sounds to stop the inspection to eliminate, do not use barely.
7. Do not remove the protective cover, safety cover, etc. on the machine and equipment, and install it when using it.
8. The die needs to undergo strict flaw detection test and shape inspection. It should be crack-free, deformed, missing, and the hardness is suitable and the size is accurate. If it is unqualified, do not use it to avoid serious damage to the machine.
9. The feeding device and the turntable are flat, high and low accurate. If it is high, it will cause leakage of powder, while at low, it will affect the quality of the tablet.
10, do not use more raw materials, because it will make more powder on the upper, more leakage under the impact, affecting the wear and tear of the parts and the loss of raw materials.
11. Do not use raw materials that are not dry, as it will cause the powder to stick to the punch surface.
12. If there are jumps or stagnation during operation, do not use your hands to avoid accidents.
13. Drive the motor first, and then turn the clutch after the operation is normal.
14. If the machine vibration is abnormal or abnormal noise occurs during use, stop it immediately.
15, the use of medium pressure should not be too large, generally measured by the load of the motor, with a 380 volt motor in the tablet when the heavy-duty current is not more than 4 amps is normal.
Fruit powder is made from pure natural fruits, mainly fruit powder processed with natural fruits as raw materials using appropriate methods. We have two kinds of fruit powder, organic fruit powder and ordinary fruit powder.
The fruit powder uses pure natural fruit raw materials, and according to the final use needs and uses of the product, through a pure physical process, a concentrated and pure powder that does not change fruit nutrients is obtained. The products include blueberry powder, apple powder, orange powder, raspberry powder, pomegranate juice powder, etc., which are mainly used in the food industry, health care industry and other industries.
Fruit Extract,Fruit Juice Powder,Organic Fruit Powder,Fruit Powder
Amazy Organic Biotech Co.,Ltd , https://www.amazyorganic.com